Category Archives: Limited and rare

SJ Ra 994 “Rapid 10”: FR recent release!!!!!!!!!!

Applause applause!!!! FR would win the Z gauge “Best Model” of the year if such awards existed. The recent release and still available 46.132.21 is based on the prototype class Ra 994 “Rapid 10” lettered for SJ.

Just 10 Ra’s were built by ASEA between 1955-1961, they were used on express train service for 30 years. The subtle resemblance to America’s F7’s is not an accident for it was the inspiration for the Ra’s design.

Typical of Scandinavian locomotives is the inclusion of snowplows modeled in metal by FR. The locomotive features brushless motors, it is recommended regular servicing at 50 hour intervals. FR advises their shop for servicing due to the engineering complexities of their locomotives, sounds like the precision workings of a fine German camera or car. On the tracks FR’s locos run smooth and quiet with bright LED lighting.

This is the 2nd Ra locomotive released by FR the 1st was the earlier Ra 846 (#46.132.01), its headlamps included 3 large aft and fore this one is based on a later prototype which included a headlamp modification. FR is aware of all the historical details and changes thus rest assured each model is well researched and accurate in Z.

FR 46.132.01 – limited release of 32 total

FR 46.132.21

Siding: Faller’s “Corner Townhouse” item #282782 card-stock building is the backdrop in this post.

NetRail: FR’s 2nd set of coaches 46.221.52

If you like rare things FR’s handmade precision models in Z are true to form; limited in number each item is historically accurate, and the current program is based on European prototypes with a heavy focus on Scandinavian railways.

More than a year ago FR started releasing their first ever ground up design and production of SJ coaches of type 1960-talsvagn. This is the 2nd set to complete the NetRail coach set thus comprising a 4 coach train set lettered for NetRail and VEOLIA Transport, Sweden.

Coaches feature interior detailing and interior lighting can be added as an accessory. The LED lighting kits are available as item #46.220.91 directly from FR’s website. USA buyers after log-in will see prices displayed in dollars without added 19%VAT.

The stated limited release of the two NetRail sets is 25 thus making these coaches instantly rare.

NetRail coach sets 1 and 2: 46.220.52 + 46.221.52. *limited numbers still available directly from FR.

Siding: Prototypical train set to pull NetRail coaches is the HECTOR RAIL class 143 locomotive (former SJ RC3) offered by FR with item #46.130.41:

Marklin 2017 Toy Fair Loco: E 94 in BLACK: 88228!!!!

The 2017 Toy Fair Loco 88228 is painted and lettered in celebration of Theodor Friedrich Wilhelm Marklin’s 200th birthday. The very attractive release of another E 94 this time with black paint scheme and red handrails based on a fictional prototype. I use the word “another” in jest, one never tires of this electric locomotive with articulated frame.

Presented in a wooden display case the locomotive is further packaged in a box printed with illustrations of Marklin’s historical articles preceding their specialty in manufacturing trains.

Features new generation of brushless motor and LED lighting.

 

FR continues to release new coaches in Z for SJ!

Two coach sets painted and lettered for SJ are now available from FR, and they include matching sets in the paint scheme for 1960’s thru 1990 thus the paint scheme is brown. FR’s modeling of these coaches includes interior detailing and trucks pre-drilled for accessory lighting.

46.220.02- 1960-talsvagn brun A+B two car set: 1- A2 5138, 1st class and 1- B5FRT 4945, 2nd class.

46.221.02- 1960-talsvagn brun B+B two car set: 1-Bo5 4752, 2nd class and 1- Bo5 4774, 2nd class.

Siding: 3 additional SJ coaches are available from FR painted and lettered for commuter traffic: 46.220.12 + 46.221.11.

FS Italia 2 car freight set by FR

The quick sell-out of a new release freight car set is due to the desirability of the extreme precision of its manufacturer FR plus limitation of 32 total worldwide.

Painted and lettered for FS-Italia (Ferrovie dello Stato) this two car set includes 1- Carro tipo Ghms peaked roof boxcar and 1- type E steel gondola.

Construction: injection molded plastic with metal chassis.

Item number 39.012.02

Note: FR Freudenreich items can be purchased directly from the manufacturer or quality-toys-trains on Ebay.

Marklin Special Imprints: 8600 Series Cars

In the late 1970’s thru now Marklin Special Imprints have been available on a very limited basis. As older collections are dismantled and sold these rarities can only be found occasionally on Ebay. Growing a collection of special imprints takes time and commitment due to their very limited availability, but the hunt is fun! Marklin has continued to produce special imprints cars mostly commemorating train events, but the early cars celebrated a vast array of products and manufacturers with very exciting graphics and always featuring the Marklin “m”. The Marklin “m” on the sides of these cars indicates printing by Marklin versus its omission on privately printed cars known as “Industry Prints” equally rare and sought after.

In the Marklin Special Imprint category is the 8600 type refrigerator car, this car type has been used more than any other for special imprints possibly owing to its smooth sides.

Printed in small numbers these commissions are often limited to 100-200 worldwide with the Swiss Hbis car types printed in editions of 300 and others of 500. A good reference for SMI’s is Koll’s Spezial Katalog 1996 + 1997, both highlight year produced, edition size and value. Pricing SMI’s is tricky business possibly due to their infrequent appearance in the market, but rare items tend to be hard to price in general.

Here are four recent finds on Ebay:

1. NORTHEIMER DIAT PILS, Koll’s #87018 (year produced 1987), edition: 100

2. DAB (Dortmunder Actien-Brauerei) Pilsener, produced in 1998 to commemorate the Intermodellbau ’98 1-5 April 1998

3. Lohrer Bier, Koll’s #88023 (year produced 1988), edition: 100

4. Bad Vilbeler Ur Quelle, Koll’s #88010 (year produced 1988), edition: 200

Siding: Koll’s published 4 books for mini-club collectors: KOLL’S PREIS-KATALOG MARKLIN Spur Z 1996 (standard releases), KOLL’S SPEZIAL KATALOG 1996 (SMI reference book), KOLL’S PREIS-KATALOG MARKLIN Spur Z 1997 (standard releases), KOLL’S SPEZIAL KATALOG 1997 (SMI reference book). The two standard release books are fun to look at, but the ultimate guide for standard releases is COLLECTION Marklin Spur Z released in 2015 by Thomas Zeeb, this book was released in a special boxed edition with the 2015 Toy Fair loco 88422: BR 111 with experimental paint scheme. Note: Marklin loco 88422 was originally released with the book, but it is also being sold now without the book, before you order one ask the dealer if it includes the book.

Engineering Perfection: Marklin E 18 in ‘Z’!

I recently purchased a rare variant of the E 18 electric locomotive in Z by Marklin, it arrived as a used working model, but with a fair amount of dirt and hairs strangling the axles. Cleaning it up included taking it apart and removing the dirt and grime under the hood, but it also included removing excess oil that even found its way under the circuit board. No HOS (hardened oil syndrome) to deal with, but over oiling has its issues including attracting dust and damaging the motor, in this case not much damage occurred to the locomotive.

This post is not so much inspired by the normal reporting of mini-club locomotive maintenance instead it is one that was inspired by the brilliant engineering and design of the E 18 for mini-club.

Marklin does not apply the same rules and principles when designing a mini-club loco: same motor and chassis different shell, no Marklin designs each locomotive class from the ground up thereby insuring the prototype is accurate in 1:220 scale and operates as flawlessly as we have all come to expect from mini-club operation!

Marklin 88082: rarest E 18 variant from 2004

The E 18 is an example of one such mini-club locomotive design that incorporates unique engineering and casting that is also meant to be taken apart and repaired when the need arises.

Taken apart this locomotive has a lot of parts that work flawlessly in the assembled locomotive including two gears that sit on posts within the frame and two large gears allowed to float on their axles.

above photo: right- small metal gear sits on post within frame as well as a second one not pictured, 2 additional gears one synthetic with two sets of gearing sit posts that are inserted through frame body

above photo: left- drive wheels that float on their axles pictured left are assembled in slots on the motor end of frame, two drive wheels right use thinner gears that are permanently fixed in the center of axles which are thicker than floating axles.

The design concept is simple: gather electricity from the wheels by way of a circuit board, the turning worm gear (transmission) on the motor engages with gearing that engages all the way down to the wheels thereby making all wheels drive wheels except for the pilot wheels.

Note: plastic mini-club loco shells are removed without damage with super thin synthetic guitar picks, do not use metal screwdrivers famously illustrated in the Marklin instruction manuals boxed with the locomotives.

With the shell off the cast wheel details are carefully pulled off, they are simply held onto the frame with posts!

Circuit board is not held under clips as with other locomotives, and one screw is all that is required to hold it in place.

The motor is screwed to the frame with 2 brackets each installed with two screws. Note: if you are at this point in restoration it is advisable to remove the motor and clean the frame under it. It is also a good idea to test the motor out of the frame, inspecting the brushes is also a good idea at this point.

After cleaning all the gears replace in the frame with the two gears on posts first followed by the large gears (2 gears that are designed to float on their axles are installed on the motor side of the frame, thickness of these axles also match the machining on the frame).

Note: use care to prevent bending of the copper leads on sides of frame.

Final steps: clipping on the wheel detail sections and then shell: Voila!!!!!

Variants of the German E 18 in mini-club:

Marklin class E 18 for DB (88080) Era III:

Marklin class 118 for DB (88081) Era IV:

Marklin class 1018 for OBB (88082) Era IV:

Marklin class E 18 42 for OBB (81441: trainset with coaches) Era III:

Siding: no other Z scale loco is designed to be taken fully apart and easily assembled as mini-club: diesel and electrics are easier than steam and non articulated are easier than articulated.

Siding: all class E 18’s are sold out at the factory, but Walthers still has the 81441 trainset available with beautiful green livery and 4 skirted coaches.

 

Micro-Structures and American Prototype Architecture for Z

Miller Engineering released a line of buildings kits years ago called Micro-Structures designed along the lines of typical architecture found in many small American towns. If you visit Main Street in many USA towns the original buildings haven’t changed much since they were built in the late 19th century, the towns themselves have changed dramatically and some buildings have gone through facelifts and demolition here and there, but for the most part the old buildings are intact thus modeling most any era of American railroading is possible with these building kits.

V101- Victorian House: “Empire” (note: additional scoring is required with this kit)

V606- Victorian House: “The Victoria”

The concentration of the line was on Main Street, but it also included a few Victorian houses that rounded out the line nicely. Note: I am using the past tense because unfortunately the line was discontinued with only a few new kits available here and there from dealer old stock. Ebay is a good source as is ZScaleHobo.com. I found a local dealer who had a few left over kits which were very popular in their day and should be today; they are well designed in historical scale and detailing plus well made out of heavy gauge etched brass.

303- K.C.’s Hardware Store (note: features printed windows with store logo) lime sometimes appears over time in mortar joints and bricks, I applied diluted white paint followed by wiping off to give this effect

404- The Triangle Hotel & Bar (note: features printed window masking for the street level windows as well as clear acetate for the other windows) building as it appears right after painting but before window glazing. Typical building type for a mid size town, but this design first appeared in NYC, that building is called not surprisingly the “Flat Iron Building”

505- Crestline Theater (note: two options for marquee include a solid marquee with etched movie now showing or a cut out marquee designed to hold a paper now showing sign, this building was built with solid marquee) detailing is so good with this kit that a depiction of can lights above the doors is included that look great lit

With a few exceptions the kits go together quite easily, but I found the large Victorian “Empire” House to have shallow scoring lines for bending in this case further scoring was required. Overall the Empire house was the most difficult of the group to make.

606- Pitman’s Deli (note: excellent detailing with printed store windows and beautiful awning, plus recessed door)

I found some kits came with acetate for the windows while others did not, and a couple had just enough for street side windows with very nice printed signage.

901- City Fire Station (note: I tried building this kit years ago with the recommended Super Glue, it was a disaster and tried these kits again until this Fall. Solder is the way to go for me!)

One obvious advantage with these kits is lighting, they will not leak light as the metal is opaque, but you must fashion windows masks or partition walls for realistic effects.

801- Townhouse #2 (note: under construction the model is assembled but prepping it for painting will include sanding solder joint smooth and bending to make the building sit flush, followed by a good cleaning with diluted Dawn, warm water and a soft toothbrush, green residue on building is flux which washes off easily with warm water and original blue Dawn)

Prepping the kits for assembly takes time, any rough edges must be sanded or filed. And after assembly the buildings need thorough cleaning to remove solder flux or other debris. Super Glue or soldering are the choices for assembly, but I prefer soldering due to the speed and control of this method. Soldering is easy if you use flux in addition to the solder with flux. I solder at 750 degrees and place water soluble flux at the area to be soldered with a toothpick. Note: solder melts and follows the source of heat, try to avoid applying solder directly to the soldering iron tip.

100- City Scoop (note: this is the only kit that requires Super Gluing, it is made of stainless steel and solder will not adhere) this building features great detailing including ice cream machines and work table on the interior, plus picnic tables, air conditioning unit and trash cans on the exterior. I had fun with this kit and painted a whimsical ice cream cone. I also left the interior natural stainless steel, but I painted the ice cream machines with silver solvent based paint and painted the outer edge of the ice cream cone with metallic copper solvent based paint just to catch a sparkle there. (note: if you discover a build-up of Super Glue after its cured it can be removed easily with a razor blade and wear gloves working with Super Glue!!!!!!!!!!)

Note: preparation of the building will include sanding or filing smooth any solder ridges or residual glue that will otherwise show up under a thin layer of paint.

Window glazing is glued in place after painting with 5 minute epoxy. As stated earlier acetate was missing in some kits I bought or not enough was included, if you build Archistories kits use some of the leftover acetate as they are very generous at Archistories.

5 minute epoxy might be the best option for securing these buildings to the layout if it is portable otherwise they sit flush to the surface and anchoring may not be required.

The small buildings in this line-up require simply cementing window details in place then folding buildings sections together and cementing. The roof requires bending along sides and molding embellishments before attaching to building. Note: fold the front section of roof first before side sections, a separate folded section goes over the front of the roof thereby giving a nice finishing touch thus do not cement the roof until this part goes on! Note: everything is outlined well in the instructions, my notes are simply to highlight important aspects that arose for me.

These buildings look better in person, and even better with a GG1 rolling by capping off the hard work and meticulous attention to detail involved with their construction. And your family will be proud of your good fortune!

No complaints about these kits, they were fun to build and modify as needed!!! And soon to be very collectible!

Siding: essential brass bending tool is “The Bug”

Battery Powered Locomotive from 1929? YES Behnke!

A locomotive that will surely garner attention on a Z layout is this small battery powered locomotive and trailer based on the prototype from 1929: Behnke release “1929 AKKUTRIEBWAGEN Muller.

Built by G. Muller in 1929 the locomotive appears to have been used for MOW service and yard work. Standing room only in the cabin this was a no frills work a day probably every day workhorse.

I sprayed the completed model in a dark red brown, followed by an inky black to top structures and finished with dry brush in a very dark gray to accentuate the details of the trucks and platforms. Headlamps are rendered in bright white paint with very fine brush.

Note: Behnke kits do not provide couplers, wheel sets or buffers, this model is awaiting buffers from FR available later in 2018.

Nagel & Kamp railway crane by Peter Behnke

Another interesting railway vehicle is this early railway crane by Nagel & Kamp released in Z by Behnke.

As with other Behnke kits wheel sets and buffers have to be purchased separately, they are available from FR and Marklin.

An interesting and early crane that will add interest to a siding or alongside a railway building.

Assembly was easier than other Behnke kits but still challenging as the parts are small and bendable joints easily break. A little weight was applied to the inside of cabin to prevent it from tipping over. Window glazing can be installed although I chose not to.

Crane boom has a fixed pitch and a winding drum is not depicted , I used a fine brown thread for the rigging line affixed to a beam that I had to supply.