Category Archives: Limited and rare

FR: 46.815.01 Gbls boxcar in metal

The German type Gbls boxcar has been modeled in all scales as it is an important freight car commonly used for many years in Europe. A good solid construction and design make this a long lasting boxcar that travels throughout much of Germany and its neighboring countries.

FR has had their version in Z featured on the FR website for sometime thus it is available to order today. It features full medal construction, marklin couplers and modern updates to the prototype featured in the model: 46.815.01.

FR’s German made Gbls is modeled on Era IV for the SJ.

The obvious attention to detail and prototypical accuracy sets FR’s offering apart. Separately applied details include handrails, brakes and ladders. The undercarriage includes detailing as well along with the FR logo. Handmade in small batches FR’s offerings are highly collectible. Check out the big round brass buffers!

Z-Modellbau: 3111 Nederlandse Spoorwegen (NS) class 200 locomotive

The Dutch Railways (NS) diesel electric locomotive “Sikken/Locomotor” (nicknamed SIK or Goat) is a shunting locomotive built starting in 1934 with the final locomotive built in 1951: 169 total. Operated from the outside of the locomotive, it did not feature a dead man pedal. No air compressor on the locomotive required its whistle to use spent exhaust air. A very simple and reliable shunting locomotive featuring original paint scheme modeled expertly by Dr. Andreas Scheibe of Z-Modellbau.

The Z-Modellbau 3111 locomotive features brushless/maintenance free motor, metal construction and marklin compatible couplers.

Note: Z-Modellbau’s coupler design is unique featuring a non-distracting thin metal system which does not engage with the Marklin uncoupler track, it is nonetheless a very unique and proven coupler design.

Siding: Z-Modellbau locomotives are delivered in a foam lined small blue box with brief instruction booklet.

Siding: Archistories ‘Gantry Crane’ ARC-114111 is available at zscalemonster.com and zscalehobo.com. Crane features swiveling platform and can roll on deck with its brass axles. Build is moderately difficult, I recommend building one their house kits first to become acquainted with Archistories build kits.

FR: 1960 Talsvagn Cinema and Bistro car of the SJ 46.220.31

Another new release by FR is the combination Cinema and Bistro car to supplement the 2 car sets: 46.220.32 and 46.221.32 with early 90’s paint scheme and lettering.

46.220.32

46.221.32

Based on the prototype half the car features elevated seating and cinema screen, other half features bar/bistro counter, bankettes and seating. And I am talking about the model too! Model features hand-painting of interior details thereby accentuating the elegant features inside this coach.

FR: Bio / Bistro (Cinema and Bistro) 46.220.31

Of course FR offers an LED lightpanel by Oliver Passmann custom designed for all the 1960 Talsvagn coaches, but in this case an easy modification needs to be made including filing down the slot housing the capacitor. A Dremel tool with blunt end fine grit grinding tool at low speed will remove enough of the extra floor panel giving room for the large capacitor. Note: other 1960 Talsvagn coaches do not require modification.

 

FR’s 1960 Talsvagen coach sets: 46.220.32 + 46.221.32

Furthering FR’s offering of 1960 Talsvagen coaches for SJ include the recent releases of 2 car sets: 46.220.32 includes 1- 1st class coach + 1- 2nd class coach and 46.221.32 includes 2- 2nd class coaches.

46.220.32

46.221.32

Painted and lettered for SJ following the paint scheme of the early 90’s these coaches also include the new logo: modern take on the winged logo dating back to the late 19th century which originally featured a railway wheel with chamfer and wings as seen here in a very early hat badge alongside a 1950’s updated hat badge:

Elegant bright colors exemplify modern SJ paint schemes following the originating paint scheme of red/brown with a simple boxed in SJ logo branding the 1st examples of 1960 Talsvagens.

A custom light panel comprising LED’s designed and manufactured by Passmann is available as an accessory on the FR website. Installation is not hard with the right tools including soldering iron, tweezers, magnifying goggles, and tool (Bug bending tool) for precision bending wheel wiper whiskers for electrical pick-up.

Note: Harald Freudenreich can deliver the coaches with bogies and roof panel removed to make installation of the light panel easier versus disassembling the coaches for the upgrade.

Siding: Bug bending tool is an indispensable tool for etched metal build kits, I haven’t found anything quite like it and I would highly recommend this item for every Z gauger’s tool box.

 

Marklin: 88135 newest ‘Ludmilla’ diesel

After reunification in Germany the class of diesel locomotives nicknamed ‘Ludmilla’ were reclassified BR 232 by Deautsche Bahn (DB AG) with their former life as BR 132’s of the East German railway system (DR- Deutsche Reichsbahn: 1949-1993) built starting in 1968 by the firm Voroshilovgrad (Russia).

This heavy weight freight locomotive is still in widespread use within Germany and Poland with 400 operating units. It is a beautiful and particularly impressive locomotive with two cabs and a length of 68′ 3 3/4″. More than 700 locomotives were built between 1973-1982 with 3000 hp motors and operating speed 75 mph. Other class ‘Ludmillas’ were soon retired after German reunification, but the class 232’s are still in use today nearing 50 year service record.

Marklin’s recent 2018 release of 88135 is painted and lettered for DB/Railion (Era V), it is now designated as ‘sold out’ at the factory. 88135 is the latest release in the series which includes: 88131 (2009), 88132 (2014), 88133 (2013), 88134 (2016), and 88135 (2018). Plus sets: 81450 and 81451.

Note: Marklin 88131 is based on the BR 234: rebuilt 232 with bogies allowing an increase in the  operating speed (87 mph)

Note: Marklin 88134 is based on the East German DR’s BR 132 with representative paint scheme from 1982

Note: Marklin set 81451 features the class 233 ‘Tiger’ (Ludmilla), this trainset is still available. A very nice and interesting H0 scale version of the Tiger (Ludmilla) includes the very latest cold steam technology and in digital operation can be controlled to simulate engine start-up idling (minimum exhaust), running operation (medium exhaust), and maximum exhaust, it is found under item #36431

81450 (2009/2010)

81451 (2017/2018)

88131 (2009) MHI Release

88132 (2014)

88133 (2013)

88134 (2016)

88135 (2018)

A common feature shared among all models in this class are LED headlamps and trailing lights, cab interiors suggested in white relief, superb running performance even at low speeds, excellent pulling power and varying roof equipment details specific to the prototype. A truly outstanding series of Marklin Z locomotives.

Siding: ‘BR’ designation preceding locomotive classification number is an abbreviation for the German word Baureihe which means class thus BR or class refers to locomotive classification

Siding: Archistories building kit ARC-114111 “Gantry Crane” is seen depicted in the background with Marklin 88135, it is a fine detailed kit with swiveling platform. It is available from zScalemonster.com and zScalehobo.com.

 

Lighting Unit for SJ Talsvagn: FR accessory upgrade

Scandinavian railroads are almost exclusively represented in Z by Freudenreich Feinwerktechnik (FR) which also includes Swiss and German prototypes. And less frequently PKP (Poland) and FS (Italy). Almost a year ago after many years in the plan and design stage the 1960 Talsvagn coach was released by FR in its first version with 2 “two car” sets with 1990’s paint scheme (blue with red stripe). Since this release there has been 6 more releases with early brown paint scheme (1960’s-90) and current NetRail paint scheme. Built into the design of each 1960 Talsvagn coach is the ability to retrofit a custom light panel manufactured in Germany by Passmann (Unna, Germany) and sold by FR as an accessory for this coach type. First a list of Talsvagn coaches thus far released.

FR’s releases are sometimes limited to a stated number while others are open editions, but all FR items should be considered rare as each is produced in small batches. The following is a list of 1960 Talsvagn coaches thus far:

46.220.02: open release (available to order)

46.220.12: open release (available to order)

46.220.42: limited to 25 total

46.220.52: limited to 25 total

46.221.02: open release (available to order)

46.221.11: open release (available to order)

46.221.42: limited to 25 total

46.221.52: limited to 25 total

Accessory lighting panel FR article #FR-TV #PA-512 is an LED light panel designed specifically for the 1960 Talsvagn coach, it is a flicker free lighting panel comprised of numerous LED’s which evenly illuminate in realistic terms. It is another outstanding accessory available from FR. Installation is easy (3/5) for those that have decent soldering skills. Instructions are included but lack English text which is not an issue at all because there are nearly 20 very good photographic illustrations.

I have a few notes to add to the included instructions that might be helpful for others retrofitting their coaches:

1. wheel sets pick-up the electricity from the track to power the light panel, each truck is connected with a wire to soldering points at each end of LED circuit board, insulated wheels should be located to one side of truck and this orientation should be carried out in the opposite position for other truck thus each truck’s pair of insulated wheel sets connect with different rails

2. whisker pick-ups should be carefully bent at 30 degree angle, 1.3mm brass bolt (kit includes 2) secures brass electrical pick-up to truck (FR accessory socket wrench 46.221.91 is designed for this bolt size), carefully reinstall wheel sets in aforementioned orientation. NOTE: before screwing bolt in place double check the pre-drilled hole goes all the way through truck housing otherwise the bolt will snap off!!!!!

3. one wire is included which should be cut in half or cut to length, before proceeding tin each end of wire (use of a little water soluble flux is advised), solder end of each wire to bolt protruding from truck with a little flux (touching soldering iron to bolt is better than wire to prevent melting of insulation (solder follows heat thus it is advisable to touch the thing you want to solder versus the wire, tinning the wire expedites the joining making it faster and easier)

4. reattach trucks into chassis with wire through pre-drilled hole, solder wires to solder points on circuit board, test LED panel before affixing to roof! Note: before soldering check orientation of circuit board with interior detailing, capacitors should fit snugly within compartment at end of car

5. roof attaches to circuit board with preinstalled double stick tape, but before installing double check middle clip on roof aligns with panel between window panes versus window otherwise the clip will be seen through the window and it will look terrible. Note: if a mistake is made with roof misalignment after LED panel is installed it will be very difficult to correct so double check/double check!!!! before gluing LED panel to roof!

Special Note: FR’s accessory light panel for the 1960 Talsvagn is easy to install with excellent instructions provided in a step by step format. Please do not deviate from the step by step instructions: all soldering should be quick and take place away from contact with plastic parts that melt thus do not install circuit board to roof panel before soldering wires to circuit board. And do not attempt to solder wire onto truck’s bolt after truck is reinstalled in coach body. All soldering takes place when trucks are separated from coach and circuit board is unattached to roof panel. Tinning wire before soldering makes things a lot easier as it allows for the wire to instantly grab the thing being soldered with minimal heat exchange.

 

 

SBB: FR Freight Car Set 41.345.12

The recent release of an SBB 2 car set by FR with type Xas73 ballast cars is already sold out, it took just a week for all 22 to be sold, but the obvious appeal is evident in this highly detailed metal car set.

For Era IV-VI, type Xas73 ballast cars are mechanically operated hoppers loaded with railway ballast: an operator can open and close 4 separate discharge gates by means of large handles modeled in FR’s car set.

Ballasting railway right of way is an important function of MOW services, but not many examples exist in Z at least for the SBB (Swiss Federal Railroad). Paint scheme of gray with white lettering is based on the prototype, this same paint scheme has been used with other rolling stock of the SBB not limited to MOW traffic.

Limited to 22 sets only is a very small edition compared to the sizable releases by Marklin and others. I was lucky enough to see it listed on the FR website and ordered immediately, one more reason to frequently check in with the FR website, registering your email with Harald Freudenreich will also ensure that you receive the semi-annual newsletter.

Car set comes packaged in the standard FR plastic box silkscreened with the FR logo, dense foam lining keeps the cars safe.

Pulling the ballast cars is a BR Re 4/4 II for the SBB. This general purpose locomotive was released by Marklin for Z in 2012 as item #88590.

 

 

Notes from a Marklin Insider: Precision and Z Scale

photo: Marklin 88091 KPEV BR P10  (Insider Release – 2003)

I received Marklin Insider Club News in yesterday’s mail, it features a two page 25th Anniversary chronology of the Insider Club in Z. The article highlights the collector Rolf-Dieter Woerz who is a long time Marklin collector and enthusiast, he was at the very beginning of mini-club in 1972! And he was a first year subscriber to the Marklin Insider Club!

photo: Marklin 81436 DRG BR 61 (loco from Henschel-Wegmann set – Insider Release 2005)

Mr. Woerz comments on the precision required in Z: “If you build in Z, you can’t cut corners.” How how true!

photo: Marklin 88010 DB BR 01 express locomotive and tender (Insider Release – 2012)

Whether gluing a shutter on a laser cut building or weathering rolling stock precision is demanded every step of the way. The right tools and techniques are part of this so called precision, but patience and confidence mirror the same. Research , time and experimentation help build the foundation for precision work while personal charm and expertise form the working methods that can be used for success in Z.

photo: Marklin 88053 DRG BR 53 loco and condensation tender (Insider Release – 2007)

In celebrating post 301, I hope to continue to share my insights in Z scale. And I hope to help others avoid mistakes that I have made along the way.

photo: Marklin 88183 DRG BR 18.1 express locomotive lettered for 1936 Olympics (Insider Release – 1996)

Siding: Marklin Insider Club membership in the United States is just $99/year and includes the magazines: Insider Club News, Marklin Magazine, and catalogs. It also includes an invitation to purchase Insider locos plus each member gets a free car in their selected gauge. As Florian Sieber states: “The Club is not there to make a profit, but to be a platform to promote communication.”

photo: Marklin 88294 DB BR 96 heavy freight locomotive (Insider Release – 2013)

Marklin Insider 81352: “DB Freight Train for Coal Transport”

“Remarkable things come in small packages!” An often used expression with new and veteran Marklin Z enthusiasts, but never as true as with model 81352. Here is a class 80 tank locomotive one of the smallest German steam locomotives used for shunting and general regional freight traffic exquisitely realized as a smooth running Marklin Z gauge locomotive heading 5 cars loaded with coal.

Note: photos only show 4 of the 5 coal cars!

What can be said of this locomotive referred to as “Little Bull” in the Marklin literature is all positive, it features glazed window openings, very detailed running gear with side rods of great complexity, superb weathering, LED headlamps, and brushless motor. And it looks great! Cars too!

Type 0 10 and 0 11 wagons loaded with removable coal inserts complete the Era III set.

Much care and attention to detail went into the production of this latest Insider release that will add a high level of realism to a prototypical mid century layout. Weathering was presumably applied with airbrush, but the level of quality maybe difficult to match even for the more experienced modeler.

*MBZ cardstock building #16058 (weathered) available exclusively in the United States from Reynaulds

As a bonus the train set included an unfinished brass casting of the locomotive shell, it is remarkable to see the unpainted and unfinished casting next to the finished loco which suggests the massive amount of handwork that takes place before these sets reach the collector.

A real stunner of a train set!

Siding: tucked nicely inside the small cockpit of this loco is a new brushless motor described as maintenance free, but other aspects of the loco require the usual maintenance including periodic oiling of wheels (as little as necessary which is not much) and wheel cleaning.

 

Marklin 81371: “Heavy Freight” Train Set (factory weathered)

Marklin’s Era III 81371 train set is still available but in limited supply: 499 sets. The train set features the heavy freight loco class 44 paired with 6 hoppers. Striking in appearance, the set features realistic heavy weathering and detailed running gear. Lot’s of action from greatly improved side rods is what’s going on in Z at Marklin these days: steam locos with grit and character more closely resembling their prototypes than ever before.

Manufactured well before the Second World War and through it until ’49 the BR 44 was a heavy hauler freight locomotive. Its numbers approached 2000, but not all locomotives stayed in Germany, twenty five percent stayed within the railways of PKP, OBB, CSD, SNCF, and DR after the war and today all but two remain operational.

The 81371 locomotive with operating number BR 44 1754 features 10 coupled and powered driving wheels with smoke deflectors. Weathering on the locomotive is tinted red with light but heavy application leaving all inscriptions legible which is a fine trick and difficult to achieve. The prototypical color of the weathering is suggestive of the acidity created by the mixing coal soot and steam on the sides of the iron boilers and plates.

Marklin has been slowly releasing weathered versions of locos and rolling stock after regular versions have debuted. For modelers looking for more and more realism these Marklin weathered items are tops! Surely impossible to weather as well as Marklin has done here certain talented folks out there could attempt the same with airbrushing, but color is as important as technique, and I am glad not to have to attempt it here!

*Archistories Prussian brick loco shed gives accurate scale to this loco thus providing historical context as well.

Six type Ootz hopper cars weathered with sooty black complete the set with lettering Erz IId. No coal loads are included, but the empty cars include weathering throughout their bays. This car type included two partitioned sections each with sloping hoppers for very quick dumping of bulk materials.

Siding: airbrushing results are far easier and trouble free with water based paints likewise water based final coat of clear lacquer should be considered to protect your work.

Siding: 81371 comes packaged in a carton housing cartons for 2 sets of 3 hoppers and 1 for the loco, item numbers printed on the cartons is as follows: hoppers (81371-01 + 81371-02) and loco (81371-03). Boxes are important to collectors and keeping them pristine is important too: open flap boxes with a butter knife to save from denting and dinging. And no butter on that knife!