Category Archives: German Federal Railroad (DB)

Marklin 8888: BR 10 Steam Locomotive

The first BR 10 loco was released in 1994 as a One Time Series for the MHI Program: product number 8888. Sporting a very attractive paint scheme the 8888 was delivered in blue and gray with bright red wheel spokes and matching tender trucks. A heavy cast metal shell with operating number 10 001 for the DB. Design and styling seems to scream Era III in the age of streamlining as a emblem of progress and modern aesthetics. The model produced by Marklin is a very good runner with plenty of weight to maximize the pulling potential of 4-5 coaches easily.

photos: 8888

VT 11.5 TEE Railcar: Improving Performance

Improving performance can be a bit of a misnomer when the talk circles around modifying a Marklin Z loco or other article in the mini-club line-up. Upgrading 3 pole motors to 5 pole motors is a significant boost to performance, but other improvements may deserve further research and discussion with other railroaders and their experiences.

One improvement I have heard about for many years is actually one I heartily suggest, Glenn and Sandy Stiska of Florida rewired several sets for me in the late 1990’s with this same repair. The modification I am talking about is the addition of two wires to each powered end unit of the VT 11.5 (8873) and the 2 ICE trains including the special release “Amtrak.” For many years this modification has been used with multi-train sets with more than one powered unit. Wired in parallel these early sets were poor runners because they relied on something close to perfection, if the electrical chain was broken between head loco, coaches and end unit the train would not go.

The 8873 used an early conductive coupling which connected the coaches to the powered end units that has since been redesigned: all railcars now use a new flat conductive coupling versus the early spring copper one.

photo: 8873 powered end unit with first generation coupler on left and 88731 Max Liebermann with next generation coupler on right

The original wiring included a pair of diodes for each circuit board which dropped the voltage to each powered car and only allowed each powered unit to go in one direction a contributing factor for stalling the train and/or flickering coach lights if power was interrupted which it readily did. The solution is to bypass the diodes by soldering a wire around each diode thus making it possible for each powered end unit to go in both directions.

A fine point soldering iron is recommended for the repair and just enough wire because too much would interfere with installing the shell.

Try this repair if you have a set of this type that does not run well, the results will blow you away!

Six versions have thus far been released with the last being the “Blue Star Train” with its very striking paint scheme.

Siding: removing the shell of the 8873 is accomplished by removing coupler if it is present and carefully inserting a small screwdriver in the coupler box, if the shell does not easily pop up it maybe stuck to chassis due to hardened oil which will require finessing to unseat it from the chassis, removing the shell from all other VT 11.5’s will require lifting the front of the shell and wriggling it around the permanent coupler. Caution: do not pull on a permanent coupler, it is not removable unless circuit board is removed first.

 

 

Repainting Marklin 8135 for the SJ!!!!!!!!!!!!!: Part 1

photo: FR 46.130.31 – RC-2 locomotive for SJ

Marklin has paid little attention to Scandinavian Railroads in z gauge. There have been releases such as the 4 MY locos (brilliant series!!!!) and a few interesting freight cars, but never has there been attention paid to Sweden, this country’s railroads are left up to the never ending achievements of Harald Freudenreich at FR.

photo: FR 46.816.01 – Kis 950 sliding roof car for steel slab transport on SJ

Marklin has covered the SJ railway in HO only while FR has devoted much of their time in recent memory to SJ and other Scandinavian railroads. FR offers some Swiss, German and Austrian items currently, but Harald’s devoted fans come to him for Scandinavian trains.

photo: FR 46.132.01 – Ra 987 Express Locomotive of the SJ

Some of the most interesting railroads in the World are located in some of the most interesting natural wonders in the World. Light, geography, and climate combine to create the beautiful Scandinavian landscape, but for trains it is challenging, cargo has to be protected from a rather brutal climate with some box cars lined with heavy insulation to protect from permafrost and autos transported in closed boxes. More on this topic at a later date.

photo: FR 47.812.00 – insulated box car for the NSB

The topic today is a project I have been interested in starting for awhile now, it is the repaint of Marklin 8135 coaches for the SJ Railway. Although FR has paid much attention to freight rolling stock, they have not released coaches for the SJ as of this date with one exception. An announcement was made earlier in the year that coach sets are coming to market later this year, but in the meantime I am making my own custom set using dry stencils provided by FR a couple of years ago. The exception was a proposed project of many years that was finally released last year, it was a Marklin coach modified for SJ. The prototype was based on German built coaches used in ferry service in Sweden.  In order to model the prototype FR repainted and stenciled the coach after cutting the shell to remove a window thus shortening the coach. I own this coach and the craftsmanship is flawless.

photo: FR 46.299.00 – type litt AB8k 1st and 2nd class coach for ferry service to Germany. The top coach is the modified Marklin for SJ by FR, and the bottom coach is the original standard coach by Marklin.

Why refinish the 8135 coaches and not another set of coaches? Good question! Set 8135 was released in 1991 and included coaches built in Germany that were also used on the SJ. The historical perspective was provided by FR who also provided the stencil kit for relettering the coaches and a paint chip for the correct shade of reddish brown used by SJ. Painting and other details will be discussed in Part 2 and 3 respectively.

photo: deluxe box train set “Dompfeil” of the DB

The first installment of this project is disassembly of the coaches. It is okay to be a little nervous disassembling Marklin coaches, but all things Marklin are built to take apart, each part is snapped or clipped together without glue. Repainting projects in Marklin Z are not necessarily recommended by this railroader, they potentially will diminish the collectible value, but in my case I own two 8135 sets which I like very much, turning the second set into SJ coaches is a bit necessary since I collect SJ locos built for express service.

On with the project! First step is identifying the set for repaint, in this case the historical background was already researched by FR. The set for repaint is Marklin 8135 released with a BR 03 express loco in a deep blue paint scheme. The set was released in 1991 with three 2nd class coaches and one DRG dining car. This was a deluxe boxed set presented in a high gloss illustrated carton. The running performance of this loco is superb, and it looks great to boot!

photo: 8135 locomotive and tender – BR 03

photo: 3 coaches disassembled with their respective parts including shell, trucks, weight, roof, and window glazing.

Step 2 includes the removal of the roof which is easily accomplished by very carefully pulling it off, the roof is clipped on and starting from one end seems to be the way to do this successfully.

Step 3 involves the removal of each car’s pair of trucks, carefully swivel each truck to the side for leverage and using a small screwdriver gently pry the truck off by moving back and forth around the pivot point, it will snap off. Note: torquing as seen in the photo is necessary for removal of trucks, but please use care.

Step 4 using a small pair of tweezers and starting at one end gently loosen the window glazing held in place with prongs in the base of the coach. Take note of the indents that line up with the roof clips for reassembly later.

Step 5 is removal of the weights. Using a small screwdriver remove the plastic heat points holding the weights down, weights will lift off easily from the posts in the bottom of shell.

This is one of those projects that allows a railroader to tinker with their hobby.

Good Luck and Have Fun!

Siding: this set contains parts that are snapped or clipped in place, but older coaches used glue to cement the window glazing, in the case of older coaches window glazing will more than likely pop out with gently wriggling. Reassembly of early windows is accomplished with 5 minute epoxy only, other glues use solvents that might melt plastic. NEVER use a soldering iron in and around enclosed plastic parts, micro soldering irons should only be used on heat points to attach shell to frame and coupler housings with caution!

German BR 10 Express Locomotive: 5 variations in Z!

A rather short lived and limited steam locomotive is none other than Germany’s BR 10 express locomotive of the DB, only 2 were made in 1957. They were seen as the replacement for the Class 01, but lack of locally sourced parts sidelined the elegant steam locomotive to the car shops thereby cementing a wrongly held belief that they were unreliable.

Nicknamed “Black Swans” because of their elegant appearance the BR 10’s were in service for just 11 years. Streamlining was practiced for many years in designs of steam locos, but the BR 10’s seemed to be a further refinement of this technology, instead of reducing wind resistance by sheathing a steam locomotive as was the tradition, the BR 10’s were shaped to direct the airflow in and around the locomotive while at the same time giving easy access to the running gear for daily maintenance. Cylinders could be accessed by hinged door in streamlining.

Two 4-6-2 BR 10’s were manufactured by Krupp with oil fired tenders that would replace traditional firing thereby reducing the fireman’s work by 30%.

The top speed of this locomotive class was nearly 100 miles/hour which was enough speed for express service and their time schedules, but their 22 ton axle weight limited their use to certain mainlines only.

The class 10 001 is a preserved locomotive at the railway museum Deustche Dampflokmuseum in Neuenmarkt-Wirsberg.

Marklin produced 5 variations of the BR 10 for Z including two in experimental colors and one 18 carat gold special version (88891). All locomotives with the exception of 88891 were given operating number BR 10 001.

In 1955 various color scheme proposals were submitted to highlight the new German Federal Railroad’s flagship locomotive, but it appears black with white pinstripe was the chosen color scheme.

8888 (photo) One Time Series 1994 for MHI program with blue and gray color scheme.

8889 (photo) BR 10 with black and white pinstripe was produced 1994-2008. Early examples will include the original 3 pole motors and later models have the new 5 pole. Operating number 10 001.

88891 (no photo) BR 10 commemorative model to celebrate “25 Jahre mini-club”. Loco and tender were produced in 25 carat gold. This One Time Series from 1997 included white gloves and a signed certificate.

88892 (photo) BR 10 produced in celebration of 10th anniversary of MHI program. Stunning experimental paint scheme in blue with pinstripe. Produced as a One Time Series in 2000. Originally available from MHI dealers only. Delivered in wood box.

88893 (photo) BR 10 in experimental paint scheme by Krauss-Maffei, they proposed this design August 4, 1955 and referenced the study as TLO 54801. The smoke deflectors were unique to this design, tear drop shape was to accentuate the forward thrust of the locomotive. The resolution meeting at the end of 1955 was unable to approve this design. Limited Release 2004 available at mini-club Center only. A stunning example of a locomotive that if produced would have broken new ground in steam locomotive design. Delivered in wood box.

Beyond color variations no differences appear in the four pictured locomotives with the exception of specialized smoke deflectors in the 88893. Under the hood late production 8889, 88892 and 88893 included the updated 5 pole motor.

Adding streamlined locomotives to a layout will portray the transitional period of the late 1950’s in Germany with all types of locos sharing the rails including traditional steam class 01’s, diesel and electric.

Good Luck and Have Fun!

Siding: this robust locomotive type is a strong runner with excellent pulling power due to its heavy weight. Even distribution of weight makes this an unlikely candidate to poop out in a turn-out at low speed. Derailments are equally unheard of with this fine mini-club locomotive.

Siding: Marklin 5 pole motor upgrade is possible for the 8888 and 8889 with part number E211911. Basic soldering techniques are required for this repair.

 

 

German P8 and BR 38 Steam Locomotives

Photo: Former Prussian P8 given as war reparation to SNCF following WWI.

Marklin reached back into German railroading history and realized the legendary P8 and BR 38 in ‘Z’. Note: before unification it was the P8 and after unification it was BR 38. In the Marklin line-up there are plenty of variations of the P8 and 38 steam locomotives but the tooling remained the same until the side rods and brake equipment were upgraded with the 2013 release of 88998.

So what about the history of this 4-6-0 locomotive? Nearly 4000 examples were manufactured for 18 years starting in 1908. Retirement came in 1974 after a 50 year career with 627 having been given to other countries as war reparations following WWI. Its top speed of 110km/hr was suitable for passenger trains, but it was a reliable goods train also. In my research the top speed of 110km/hr was never fully achieved in the Prussian examples due to poor running performance of the Prussian ‘box’ style tenders instead it would seem that 100km/hr was the top speed in the early years. It is noted that larger tenders were not used by KPEV due to the burdens of turning a longer loco and tender on turntables of the time. Eventually the DB fitted war time ‘tub’ style tenders to this locomotive class after WWII.

8899 is the first BR 38 produced in mini-club, 1982 to be exact. This Era III BR 38 for the DB featured the original Prussian ‘box’ style tender and 3 pole motor, it was produced until 1995. The large smoke deflectors would eventually be replaced with smaller ‘Witte’ deflectors.

88991 (photo) is virtually identical to 8899 with two notable exceptions: 5 pole motor and post-war ‘tub’ style tender. This locomotive was produced from 1998 until 2003.

The P8 painted and lettered for KPEV (Royal Prussian Railroad Administration) as a One Time Series was 88994 (photo). Released in 2006 as part of the MHI program the 88994 represents an Era I P8 with original Prussian ‘box’ style tender. KPEV locos in the Marklin line-up are heavily detailed with distinctive paint scheme, they can go with passenger or freight cars, or both.

Jumping ahead to the new era at Marklin is the 88998 (photo) BR 38 for DB. An Era III steam locomotive featuring Marklin new design concept that includes lively side rod action and detailing including well conceived brake equipment details. The movement of the side rods on this loco are elegant! Note the correct style tender for Era III and ‘Witte’ smoke deflectors. First retooling since 1982!

Rolling back the clock to 2009 is the 88999 (photo) P8 for Gr.Bad.Sts.E. (Grand Ducal Baden State Railways). This Era I locomotive was in the Marklin mini-club line-up from 2009-2014. Original Prussian box style tender and 5 pole motor. Paint and lettering in Prussian Blue with boiler straps painted to highlight the prototypes original brass ones. Note: no smoke deflector was incorporated in the early design of the P8, other design changes would happen over time including two types of smoke deflectors and tub style WWII welded tender.

Marklin’s first release of a P8 in a train set was 8130 from 1989 – 1992, the 8128 (photo) included an Era I KPEV loco and tender paired with four freight cars.

The Marklin 81420 (photo) Grand Ducal Baden State Railways train set from 2000 – 2002 included a Gr.Bad.Sts.E P8 in striking Prussian Blue paint scheme detailed with brass boiler straps, it was boxed with a 2nd class and a 3rd class coach as well as a privately owned Swiss tank car and beer car with brakeman’s cabin. Locomotive is equipped with Marklin 5 pole motor.

The 2002 One Time Release of “Sylt Auto Travel Train” 81428 (photo) was another example of a train set with mixed rolling stock, freight and passenger coaches comprising the consist. This train set from Era III included a DB BR 38 with ‘tub’ style tender, 2- coaches lettered for “Hamburg – Altona, Husum – Niebull, Westerland plus 4 low side cars with autos, camping trailers and vans as loads. An interesting train set for vacationers traveling to camping destinations, this train removed the inconvenience of driving a camping rig to the vacation spot thereby delivering rested passengers at the start of their leisure vacations. Note: first time Witte smoke deflectors used on this ‘Z’ loco type.

The Era II “Ruhr-Schnellverkehr” (Ruhr Express Service) train set 81437 (photo) was released in 2005, it was produced until 2008, but it is unlikely many were produced through this period owing to the rarity of this set. The BR 38 locomotive was joined in the set with three coaches of Prussian design: 2- 3rd class coaches with and without brakeman’s cab, and 1- 2nd/3rd class coach with brakeman’s cab (notice the colorful paint scheme on center compartments denoting 2nd class). Please take note of the Prussian design compartments each accessed by exterior doors, in express coaches of this design passengers had little time to find their compartment and climb in, less than a minute is all you were given! The Marklin coaches in this set are stunning, they are full of detail including full length running boards and decorated brass hardware. The locomotive (photo 2) also featured destination boards: Ruhr – Schnellverkehr.

Siding: to describe the brilliant running performance of this loco type in ‘Z’ as anything less than superlative would be a mistake. If you are new to collecting Marklin Z steam this loco type in any example is highly recommended: perfection on the rails!

 

Pilot Wheels: Legacy in Marklin Z

Marklin 88092 with two wheel leading truck.

With the invention of the steam locomotive in the 19th century came un-powered pilot wheels as part of its invention, they were meant to support the front end of the boiler and assist the locomotive negotiating curves. John Jervis is credited with the first locomotive design incorporating leading wheels or pilot wheels for his 1832 4-2-0 locomotive. It would be another 33 years until the design of leading wheels would be improved by William Adams, his 1865 design allowed the front bogie to slide slightly to negotiate curves and a spring mechanism to thus allow the bogie to reorient to center. A two wheel leading truck is referred to as a ‘pony’ truck, four and six wheel leading trucks are considered more stable than pony trucks for high speed service. As a point of clarification the pilot of a locomotive is located on the front of a locomotive to deflect any type obstruction which would otherwise derail the train, various designs were built into 19th and 20th century steam locomotives of a mostly filigree framework, later solid sheathing was incorporated in the streamlining of many diesel designs in the United States.

Marklin Z steam locomotives incorporate sliding lead wheel sets with a spring mechanism made of tension brass. Even in Z the leading wheels are important to running long steam locomotives successfully. It is another example of Marklin being true to the prototype even in the smallest scale.

I recently bought 88272 as ‘new dealer old stock’, it was released in the mid 2000’s as a One Time Series, it sat on a shelf for over 10 years with plenty of time for the oil to harden. I tested it at low voltage and it worked flawlessly without any hesitancy so I tried it on a large oval, the pilot wheels derailed on the first curve: hardened oil syndrome on the pilot truck pivot point as well as the trailing truck’s pivot point with no sign of hardened oil in the gearing of the driving wheels. Cleaning the loco of all the old oil and re-oiling solved the problem! Advantages with Marklin Z are the easy to diagnose and repair problems: always look for the easy answers.

After making the repair I compared the 88272 BR 42 with the 88273 BR 41 both are closely related with the same chassis and shell , leading wheels and trailing wheels on the 88273 do not include the tension brass mechanism supporting the axle on both trucks. If the slight tension created by the brass spring is too much the wheel set will deform below the surface of the driving wheels. Removing the brass tension mechanism if it is deformed or damaged is recommended, if it is left in this case derailments will ensue.

Since entering the community of Z I have been told by many that the two wheel leading truck on some Marklin Z steam locos cause derailments due to not enough weight on the front end of the locomotive, it has been advised that placing lead weights to the front end by soldering bb’s is the answer to fixing the apparent Marklin design flaw. We might all like to tinker, but as a long time collector of Marklin z gauge I found no evidence of design flaws in z by Marklin quite the opposite, I continue to marvel at locomotives and rolling stock designed for long term running characteristics which are easy to maintain and repair.

I collect Marklin mini-club as my primary railroading enterprise, but I also collect prewar Marklin 1 gauge and prewar Lionel Standard gauge. As a point of comparison I pulled out the motor and pilot wheels of my Lionel 384 from 1930. In the photos the itty bitty Marklin Z 88273 incorporates leading wheels that slide on their axle whereas the big Lionel loco restricts the leading wheels to pivot only on a vertical axis.

Photo: Lionel 384 pilot wheel and Marklin 88273: behemoth and the “Little Giant!”

Photo: Lionel 384 2-4-0 locomotive motor with driving wheels and leading wheels juxtaposed next to Marklin 88273 which incorporates a sliding axle not present in the 1930 Lionel.

I would say in closing that Marklin has already considered the leading trucks as important elements and not decoration in their design which accounts for historical accuracy and perfect operating characteristics, modification to the leading truck maybe overlooking the real problems which could be dirt or hardened oil around the pivot point or too much downward pressure from the brass tension spring. The same applies to the trailing truck. Always look for the easy answers instead of reinventing the wheel.

Good luck and have fun!

Siding: Gearing on Marklin Z gauge steam locomotives usually comprise driving wheels with connecting gears. Connecting gears are installed first followed by the driving wheels and side rods. It is a little tricky working with small parts, but the objective is to line up all of the wheel weights in correct orientation otherwise the loco will not run smoothly instead the gears will bind up. Tell those around you that you may need a 1/2 hour on your hobby or 6 hours when you make your first steam locomotive repair.

Siding: if that set of pilot wheels keeps derailing it will more than likely be dirt or hardened oil around the pivot point, pilot wheels should move freely around pivot point.

Happiness comes 1:220: Marklin 88010

Photos: Marklin 88010 “2012 Insider Model” class 01 express locomotive of the DB.

Reaching back a few years (very few years 2012) to the Insider Model of 2012 is the 88010 a superlative locomotive not only for German railroad history but also mini-club history. On its release mini-club collectors for the first time received an important German express locomotive modeled in 1:220 with detailed running gear and working side rods of an advanced state of design. “How did they do it? How could they do it?” were at least two of the questions that swirled in the ‘Z’ community. But then something truly remarkable happened Marklin advanced these design skills to each of the steam locomotive class in subsequent years. But wait they simultaneously applied the same design skills and inspiration to the diesel and electric locomotive classes. Long time collectors of Marklin Z could not have anticipated the advancements to this rarified hobby, but here we are on the other side of what many of us thought was impossible. What a great and lovely time to be part of the “mini-club” Club!

As the models come closer to the prototypes those reasons for not going ‘Z’ become evermore present: reality modeled in Marklin Z achieved at the smallest scale without compromising the prototype. Sure it is charming and fun to collect larger scales that are modeled to move freely on a layout with all the functions you would expect, but trains of other scales as we go up in size require sensitivity to length and size in order to work flawlessly with the radius curves, turnouts and special features. Z scalers appreciate those concerns are mere fodder for this scale, as such we enjoy unprecedented freedom to explore large layouts that might include multiple towns modeled with accurately represented trains in the same space a larger scale might only include a few buildings with an oval layout maybe on a 4’x8′ board. Z is limitless and the potential to build and design a large layout is not out of reach of most railroaders even those living in a small apartment in Manhattan: 1 foot of track length equals 220 feet of prototypical track length, at 6 feet we are approaching a 1/4 mile. Add a complete loop and a radius we are close to a mile. But many ‘Z’ers I have met over the years don’t limit their layout dimensions to the traditional 4×8, they have no rules. Taking over a room in a house might be a man cave to some but for others it is peace of mind for many wives and partners, but Marklin mini-club is not limited to men only it is a hobby enjoyed by women as well. What better way to spend a Saturday afternoon than reading a book on railroading, designing the ultimate layout, building a beautiful Archistories laser cut building, or cleaning and maintaining your layout and collection. The ultimate railroading experience is ‘Z’, this scale overtakes the senses as it has since 1972 and many of us ‘Z’ers are among the happiest people alive: cheers Marklin!

Siding: join the Insider Club with benefits that include the Marklin Magazin, Insider Magazine, free club car in the gauge of your choice and invitation to own Insider locos which often introduce new tooling!

 

Marklin Z: One of the Last Great Collectibles!

Photo: Insider Model 2012: 88010 – BR 001 for DB (no longer available)

Are we collecting or are we acquiring: that is the question. When Marklin Z comes into a collection a bit of railroad history is preserved and a commitment is made by this generation to future generations that hold that Marklin’s history and the greater history of railroading is worth preserving.

Photo: Special Imprint (SMI) 88820: “Swiss Cheese” class Am 4/4 pictured with type Hbis freight car also featuring “Swiss Cheese” paint scheme. (no longer available)

Marklin Z gauge is one of the last great collectibles, it will persevere well into the future, and what has been released thus far since 1972 are limited and rare. Rarity is well liked by collectors of all types, but collecting Marklin mini-club (Z) is truly unique from all other collectibles due to their leadership and innovation in z gauge. There are other companies some small and some large producing z gauge products but Marklin is linked to z gauge by the very fact they invented it in 1972, they continue that history today with innovations including true catenary operation through roof equipped pantographs on their electric locos, realistic working side rods on the steam engines, and numerous diesel loco types including the Russian Ludmillas.

Photo: Export Model for France 2003: 88063 – Reihe 232 TC (no longer available)

Many collected “toys” (only time this word will be used on this blog because railroading is serious business! I’m kidding its loads of fun too!!!) these days are secondary market items from long defunct and beloved companies such as Buddy L from the 20’s. It is exciting to dig around a find some rare item that has not been made for 80-100 years or more, but with Marklin anyone can jump in and start collecting from a company in business since 1859. Buy a mini-club loco today and within a year or two or even a few months it will be out of production and already a collectible. Keeping the condition of your new train pristine is part and parcel to collecting anything, but with Marklin this extends to keeping the box in good condition. Want to run a train on a layout simply select the railroad you want to model and keep the other fine locos and rolling stock on display, displaying is just as much fun as driving those trains.

Photo: Marklin Magazin Edition 88953: BR 74 with lettering and Prussian Blue paint scheme for Marklin Magazin (still in production). Note: 1st locomotive release for the “Marklin Magazin” editions.

For collectors Marklin Z new releases are limited and rare falling into several categories: MHI Releases, Special Imprinted Editions, Export Models, Insider Models, Museum Editions, Marklin Magazine Editions, and general releases. Marklin Handlers Initiative includes releases only available to dealers that subscribe to the MHI program, this subscription includes ordering everything Marklin releases, MHI’s are One Time Series. Export Models are limited to distribution in the given country the release represents thus Swiss Export Models are distributed to Swiss dealers in a One Time Series. Insider Models are available only to Insider Members who maintain year long membership in the insider Club for about $100/ year with many benefits. Museum Editions are car sets inspired by companies with ties to Goppingen, Germany the home of Marklin’s headquarters. Usually housed in a specially printed tin box museum editions include a freight car and sometimes a cast metal truck or van. Marklin Magazin Editions are distributed in the United States by Walthers, these One Time Series freight cars usually depict a new car type, they are always painted Prussian Blue with Marklin Magazin insignia, and sometimes the car designs are inspired by the magazine’s printing production including one car that included a load of reams of printing paper. General Releases are those cars and locos that are announced by Marklin and commonly distributed throughout the world, but aside from the perception of wide distribution these items are still very limited and rare with popular releases selling out fast. Of the categories so described Special Imprints and Export Models are the most difficult to collect with secondary market dealers being the only source for these with the exception of direct purchase from German dealers including those with listings on Ebay.

Photo: Marklin MHI release (2016) 88216: BR 212 (diesel) for DB AG (out of production: still available)

Photo: Marklin regular release (2013) 88998: BR 38 Era III (former Prussian P8) passenger loco with tub style tender (no longer available). Note: BR 38’s have been in the Marklin mini-club program for years including trainsets, but the 88998 was the first generation of this loco type with highly detailed side rods and running equipment. This is one of favorite mini-club locos, it is a real pleasure to watch pulling Prussian coaches its action on the rails is melodic.

Part of the fun of collecting Marklin Z is rarity, this singular aspect of this hobby is underscored by small productions of one time series in multiple categories: Marklin Z the readymade collectible!

 

Trains are Trains – Marklin Models of Trains are something different and greatly so!

Marklin 88855: BR 03 Express Locomotive of the DB

A subtle thought occurred to me the other day, I was thinking about my last post on Scandinavian snowplow locos of the SJ in Sweden while having a brief moment of reflection during work as a photographer of architecture and interior design. My Wife and I work together so moments of repose sometimes happen during brief interludes moving equipment from the shot just taken to the next.

Marklin 88063: Serie 232 TC of the SNCF

I am very impressed with the offerings of Marklin and their z gauge line in the last five years, the following is a brief post and interlude in the normal technical and historical postings thus far presented at ZTrainsWeekly. This post is dedicated to the type of collector I have met on many occasions hanging out in train stores across the country, train meets and clubs, those that have taken on collecting expensive tiny trains because holding them in their hands and marveling at their striking detail and charm make them happy.

Marklin 88833: Serie 150 Y of the SNCF

So what does a Z gauge railroad loco or rolling stock have in common with the prototype railroad equipment of a particular railroad. First they are in a scale of 1:220 so every 1 inch translates to 220 inches in prototypical scale thus accurately reduced by Marklin in length, height and width dimensions. Graphics and lettering are correctly rendered by Marklin fitting accurately in historic timeframe. Detailing of trucks and equipment appear to show few differences with the prototype. Working headlamps and running lights are sometimes designed into the model and for some vary little with the prototype. But if we start with the prototype and compare it to the Z railroad model of Marklin few similarities can exist including actual equipment operation those being sanders, air brakes, working engines and the like. I hope I haven’t lost the interest of my readers, I am close to making this posting worth while if you have been queried by those that have yet to be bitten by the railroading hobby.

Marklin 88134: BR 132 of the DR

The model can only be a version of the prototype, but an impression of the prototype is far better than real diesel model locos running on diesel fuel throughout your house killing your houseplants and annoying your wife or steam and arcing electric ones. The comparison between the prototype and the model resides in the idea that the prototype surfaces on the rails in front of us and embodies history, design and awe whereas the model railroad elicits its connection to the prototype but also triggers our imagination thus connecting us to the models in serious and creative ways. All model railroad collectors are connected in this way, we can study the history of the prototype and marvel at its representation as a model as something else thus collecting the miniature is our railroading connection not limited but expansive.

Marklin 88106: BR 05 of the DRG and Marklin 88075: Class J-2 of NYC

Models of trains and their prototypes were built side by side since railroads began in the 19th century, Marklin was the first to successfully manufacturer commercially available miniature trains. Cheers to Marklin and another 158 years of outstanding trains!

Marklin 88687 BR 101 Electric Loco: Simple Repair

A quick note concerning Marklin’s line of BR 101’s. I just received the older 88687 which is a member of the Bayer series of class 101’s, it arrived with one buffer off.  Sooner or later you might come across this and maybe the first inclination is to glue it back on, but please don’t! The original and brilliant design included a clip system without any glue entering the mix. The black part that holds the buffers works also as a clip to hold the LED’s in place, two prongs on the black buffer part engage with tiny holes in shell and wow its back together again. It is of course part of the natural occurrence with Z to have something come loose, but rarely if ever is this due to broken or defective parts so stay away from the glue unless the loco dropped to the concrete floor and cracked, in this case 5 minute epoxy is the way to go.