Category Archives: Marklin Z

VT 11.5 TEE Railcar: Improving Performance

Improving performance can be a bit of a misnomer when the talk circles around modifying a Marklin Z loco or other article in the mini-club line-up. Upgrading 3 pole motors to 5 pole motors is a significant boost to performance, but other improvements may deserve further research and discussion with other railroaders and their experiences.

One improvement I have heard about for many years is actually one I heartily suggest, Glenn and Sandy Stiska of Florida rewired several sets for me in the late 1990’s with this same repair. The modification I am talking about is the addition of two wires to each powered end unit of the VT 11.5 (8873) and the 2 ICE trains including the special release “Amtrak.” For many years this modification has been used with multi-train sets with more than one powered unit. Wired in parallel these early sets were poor runners because they relied on something close to perfection, if the electrical chain was broken between head loco, coaches and end unit the train would not go.

The 8873 used an early conductive coupling which connected the coaches to the powered end units that has since been redesigned: all railcars now use a new flat conductive coupling versus the early spring copper one.

photo: 8873 powered end unit with first generation coupler on left and 88731 Max Liebermann with next generation coupler on right

The original wiring included a pair of diodes for each circuit board which dropped the voltage to each powered car and only allowed each powered unit to go in one direction a contributing factor for stalling the train and/or flickering coach lights if power was interrupted which it readily did. The solution is to bypass the diodes by soldering a wire around each diode thus making it possible for each powered end unit to go in both directions.

A fine point soldering iron is recommended for the repair and just enough wire because too much would interfere with installing the shell.

Try this repair if you have a set of this type that does not run well, the results will blow you away!

Six versions have thus far been released with the last being the “Blue Star Train” with its very striking paint scheme.

Siding: removing the shell of the 8873 is accomplished by removing coupler if it is present and carefully inserting a small screwdriver in the coupler box, if the shell does not easily pop up it maybe stuck to chassis due to hardened oil which will require finessing to unseat it from the chassis, removing the shell from all other VT 11.5’s will require lifting the front of the shell and wriggling it around the permanent coupler. Caution: do not pull on a permanent coupler, it is not removable unless circuit board is removed first.

 

 

Under the Hood: Marklin Z Rotary Snowplow

A brief look under the hood of Marklin’s “Rotary Snowplow” in z scale reveals engineering that is both functional and well conceived.

Two worm gears meet up at 90 degrees to turn the cutting wheel that is powered by the 5 pole motor. A heavy metal frame is the foundation for the motor which receives its power directly from the rails without the need of a circuit board, the motor leads are soldered to wires leading to trucks: one wire to each truck soldered to a power pick-ups in the form of spring copper. A unique solution that I haven’t seen in any other mini-club train except for the 3 Rotary Snowplow sets. The overall weight of the snowplow is equal to a locomotive thereby giving it good traction.

To access the interior of the snowplow simply lift off shell, it slides on snugly without clips, I recommend working front and back gently until it lifts off thus allowing the brushes to be replaced: part number 89891.

More than 8 1/2 inches in length the mini-club Rotary Snowplow is an impressive machine.

Take a look at part two of the post featuring customization of the loco and repair notes.

Good Luck and Have Fun!

Repainting Marklin 8135 for the SJ!!!!!!!!!!!!!: Part 1

photo: FR 46.130.31 – RC-2 locomotive for SJ

Marklin has paid little attention to Scandinavian Railroads in z gauge. There have been releases such as the 4 MY locos (brilliant series!!!!) and a few interesting freight cars, but never has there been attention paid to Sweden, this country’s railroads are left up to the never ending achievements of Harald Freudenreich at FR.

photo: FR 46.816.01 – Kis 950 sliding roof car for steel slab transport on SJ

Marklin has covered the SJ railway in HO only while FR has devoted much of their time in recent memory to SJ and other Scandinavian railroads. FR offers some Swiss, German and Austrian items currently, but Harald’s devoted fans come to him for Scandinavian trains.

photo: FR 46.132.01 – Ra 987 Express Locomotive of the SJ

Some of the most interesting railroads in the World are located in some of the most interesting natural wonders in the World. Light, geography, and climate combine to create the beautiful Scandinavian landscape, but for trains it is challenging, cargo has to be protected from a rather brutal climate with some box cars lined with heavy insulation to protect from permafrost and autos transported in closed boxes. More on this topic at a later date.

photo: FR 47.812.00 – insulated box car for the NSB

The topic today is a project I have been interested in starting for awhile now, it is the repaint of Marklin 8135 coaches for the SJ Railway. Although FR has paid much attention to freight rolling stock, they have not released coaches for the SJ as of this date with one exception. An announcement was made earlier in the year that coach sets are coming to market later this year, but in the meantime I am making my own custom set using dry stencils provided by FR a couple of years ago. The exception was a proposed project of many years that was finally released last year, it was a Marklin coach modified for SJ. The prototype was based on German built coaches used in ferry service in Sweden.  In order to model the prototype FR repainted and stenciled the coach after cutting the shell to remove a window thus shortening the coach. I own this coach and the craftsmanship is flawless.

photo: FR 46.299.00 – type litt AB8k 1st and 2nd class coach for ferry service to Germany. The top coach is the modified Marklin for SJ by FR, and the bottom coach is the original standard coach by Marklin.

Why refinish the 8135 coaches and not another set of coaches? Good question! Set 8135 was released in 1991 and included coaches built in Germany that were also used on the SJ. The historical perspective was provided by FR who also provided the stencil kit for relettering the coaches and a paint chip for the correct shade of reddish brown used by SJ. Painting and other details will be discussed in Part 2 and 3 respectively.

photo: deluxe box train set “Dompfeil” of the DB

The first installment of this project is disassembly of the coaches. It is okay to be a little nervous disassembling Marklin coaches, but all things Marklin are built to take apart, each part is snapped or clipped together without glue. Repainting projects in Marklin Z are not necessarily recommended by this railroader, they potentially will diminish the collectible value, but in my case I own two 8135 sets which I like very much, turning the second set into SJ coaches is a bit necessary since I collect SJ locos built for express service.

On with the project! First step is identifying the set for repaint, in this case the historical background was already researched by FR. The set for repaint is Marklin 8135 released with a BR 03 express loco in a deep blue paint scheme. The set was released in 1991 with three 2nd class coaches and one DRG dining car. This was a deluxe boxed set presented in a high gloss illustrated carton. The running performance of this loco is superb, and it looks great to boot!

photo: 8135 locomotive and tender – BR 03

photo: 3 coaches disassembled with their respective parts including shell, trucks, weight, roof, and window glazing.

Step 2 includes the removal of the roof which is easily accomplished by very carefully pulling it off, the roof is clipped on and starting from one end seems to be the way to do this successfully.

Step 3 involves the removal of each car’s pair of trucks, carefully swivel each truck to the side for leverage and using a small screwdriver gently pry the truck off by moving back and forth around the pivot point, it will snap off. Note: torquing as seen in the photo is necessary for removal of trucks, but please use care.

Step 4 using a small pair of tweezers and starting at one end gently loosen the window glazing held in place with prongs in the base of the coach. Take note of the indents that line up with the roof clips for reassembly later.

Step 5 is removal of the weights. Using a small screwdriver remove the plastic heat points holding the weights down, weights will lift off easily from the posts in the bottom of shell.

This is one of those projects that allows a railroader to tinker with their hobby.

Good Luck and Have Fun!

Siding: this set contains parts that are snapped or clipped in place, but older coaches used glue to cement the window glazing, in the case of older coaches window glazing will more than likely pop out with gently wriggling. Reassembly of early windows is accomplished with 5 minute epoxy only, other glues use solvents that might melt plastic. NEVER use a soldering iron in and around enclosed plastic parts, micro soldering irons should only be used on heat points to attach shell to frame and coupler housings with caution!

German BR 10 Express Locomotive: 5 variations in Z!

A rather short lived and limited steam locomotive is none other than Germany’s BR 10 express locomotive of the DB, only 2 were made in 1957. They were seen as the replacement for the Class 01, but lack of locally sourced parts sidelined the elegant steam locomotive to the car shops thereby cementing a wrongly held belief that they were unreliable.

Nicknamed “Black Swans” because of their elegant appearance the BR 10’s were in service for just 11 years. Streamlining was practiced for many years in designs of steam locos, but the BR 10’s seemed to be a further refinement of this technology, instead of reducing wind resistance by sheathing a steam locomotive as was the tradition, the BR 10’s were shaped to direct the airflow in and around the locomotive while at the same time giving easy access to the running gear for daily maintenance. Cylinders could be accessed by hinged door in streamlining.

Two 4-6-2 BR 10’s were manufactured by Krupp with oil fired tenders that would replace traditional firing thereby reducing the fireman’s work by 30%.

The top speed of this locomotive class was nearly 100 miles/hour which was enough speed for express service and their time schedules, but their 22 ton axle weight limited their use to certain mainlines only.

The class 10 001 is a preserved locomotive at the railway museum Deustche Dampflokmuseum in Neuenmarkt-Wirsberg.

Marklin produced 5 variations of the BR 10 for Z including two in experimental colors and one 18 carat gold special version (88891). All locomotives with the exception of 88891 were given operating number BR 10 001.

In 1955 various color scheme proposals were submitted to highlight the new German Federal Railroad’s flagship locomotive, but it appears black with white pinstripe was the chosen color scheme.

8888 (photo) One Time Series 1994 for MHI program with blue and gray color scheme.

8889 (photo) BR 10 with black and white pinstripe was produced 1994-2008. Early examples will include the original 3 pole motors and later models have the new 5 pole. Operating number 10 001.

88891 (no photo) BR 10 commemorative model to celebrate “25 Jahre mini-club”. Loco and tender were produced in 25 carat gold. This One Time Series from 1997 included white gloves and a signed certificate.

88892 (photo) BR 10 produced in celebration of 10th anniversary of MHI program. Stunning experimental paint scheme in blue with pinstripe. Produced as a One Time Series in 2000. Originally available from MHI dealers only. Delivered in wood box.

88893 (photo) BR 10 in experimental paint scheme by Krauss-Maffei, they proposed this design August 4, 1955 and referenced the study as TLO 54801. The smoke deflectors were unique to this design, tear drop shape was to accentuate the forward thrust of the locomotive. The resolution meeting at the end of 1955 was unable to approve this design. Limited Release 2004 available at mini-club Center only. A stunning example of a locomotive that if produced would have broken new ground in steam locomotive design. Delivered in wood box.

Beyond color variations no differences appear in the four pictured locomotives with the exception of specialized smoke deflectors in the 88893. Under the hood late production 8889, 88892 and 88893 included the updated 5 pole motor.

Adding streamlined locomotives to a layout will portray the transitional period of the late 1950’s in Germany with all types of locos sharing the rails including traditional steam class 01’s, diesel and electric.

Good Luck and Have Fun!

Siding: this robust locomotive type is a strong runner with excellent pulling power due to its heavy weight. Even distribution of weight makes this an unlikely candidate to poop out in a turn-out at low speed. Derailments are equally unheard of with this fine mini-club locomotive.

Siding: Marklin 5 pole motor upgrade is possible for the 8888 and 8889 with part number E211911. Basic soldering techniques are required for this repair.

 

 

German P8 and BR 38 Steam Locomotives

Photo: Former Prussian P8 given as war reparation to SNCF following WWI.

Marklin reached back into German railroading history and realized the legendary P8 and BR 38 in ‘Z’. Note: before unification it was the P8 and after unification it was BR 38. In the Marklin line-up there are plenty of variations of the P8 and 38 steam locomotives but the tooling remained the same until the side rods and brake equipment were upgraded with the 2013 release of 88998.

So what about the history of this 4-6-0 locomotive? Nearly 4000 examples were manufactured for 18 years starting in 1908. Retirement came in 1974 after a 50 year career with 627 having been given to other countries as war reparations following WWI. Its top speed of 110km/hr was suitable for passenger trains, but it was a reliable goods train also. In my research the top speed of 110km/hr was never fully achieved in the Prussian examples due to poor running performance of the Prussian ‘box’ style tenders instead it would seem that 100km/hr was the top speed in the early years. It is noted that larger tenders were not used by KPEV due to the burdens of turning a longer loco and tender on turntables of the time. Eventually the DB fitted war time ‘tub’ style tenders to this locomotive class after WWII.

8899 is the first BR 38 produced in mini-club, 1982 to be exact. This Era III BR 38 for the DB featured the original Prussian ‘box’ style tender and 3 pole motor, it was produced until 1995. The large smoke deflectors would eventually be replaced with smaller ‘Witte’ deflectors.

88991 (photo) is virtually identical to 8899 with two notable exceptions: 5 pole motor and post-war ‘tub’ style tender. This locomotive was produced from 1998 until 2003.

The P8 painted and lettered for KPEV (Royal Prussian Railroad Administration) as a One Time Series was 88994 (photo). Released in 2006 as part of the MHI program the 88994 represents an Era I P8 with original Prussian ‘box’ style tender. KPEV locos in the Marklin line-up are heavily detailed with distinctive paint scheme, they can go with passenger or freight cars, or both.

Jumping ahead to the new era at Marklin is the 88998 (photo) BR 38 for DB. An Era III steam locomotive featuring Marklin new design concept that includes lively side rod action and detailing including well conceived brake equipment details. The movement of the side rods on this loco are elegant! Note the correct style tender for Era III and ‘Witte’ smoke deflectors. First retooling since 1982!

Rolling back the clock to 2009 is the 88999 (photo) P8 for Gr.Bad.Sts.E. (Grand Ducal Baden State Railways). This Era I locomotive was in the Marklin mini-club line-up from 2009-2014. Original Prussian box style tender and 5 pole motor. Paint and lettering in Prussian Blue with boiler straps painted to highlight the prototypes original brass ones. Note: no smoke deflector was incorporated in the early design of the P8, other design changes would happen over time including two types of smoke deflectors and tub style WWII welded tender.

Marklin’s first release of a P8 in a train set was 8130 from 1989 – 1992, the 8128 (photo) included an Era I KPEV loco and tender paired with four freight cars.

The Marklin 81420 (photo) Grand Ducal Baden State Railways train set from 2000 – 2002 included a Gr.Bad.Sts.E P8 in striking Prussian Blue paint scheme detailed with brass boiler straps, it was boxed with a 2nd class and a 3rd class coach as well as a privately owned Swiss tank car and beer car with brakeman’s cabin. Locomotive is equipped with Marklin 5 pole motor.

The 2002 One Time Release of “Sylt Auto Travel Train” 81428 (photo) was another example of a train set with mixed rolling stock, freight and passenger coaches comprising the consist. This train set from Era III included a DB BR 38 with ‘tub’ style tender, 2- coaches lettered for “Hamburg – Altona, Husum – Niebull, Westerland plus 4 low side cars with autos, camping trailers and vans as loads. An interesting train set for vacationers traveling to camping destinations, this train removed the inconvenience of driving a camping rig to the vacation spot thereby delivering rested passengers at the start of their leisure vacations. Note: first time Witte smoke deflectors used on this ‘Z’ loco type.

The Era II “Ruhr-Schnellverkehr” (Ruhr Express Service) train set 81437 (photo) was released in 2005, it was produced until 2008, but it is unlikely many were produced through this period owing to the rarity of this set. The BR 38 locomotive was joined in the set with three coaches of Prussian design: 2- 3rd class coaches with and without brakeman’s cab, and 1- 2nd/3rd class coach with brakeman’s cab (notice the colorful paint scheme on center compartments denoting 2nd class). Please take note of the Prussian design compartments each accessed by exterior doors, in express coaches of this design passengers had little time to find their compartment and climb in, less than a minute is all you were given! The Marklin coaches in this set are stunning, they are full of detail including full length running boards and decorated brass hardware. The locomotive (photo 2) also featured destination boards: Ruhr – Schnellverkehr.

Siding: to describe the brilliant running performance of this loco type in ‘Z’ as anything less than superlative would be a mistake. If you are new to collecting Marklin Z steam this loco type in any example is highly recommended: perfection on the rails!

 

Marklin 81001: “Leig-Einheit” Train Set

If you happen to own the Z Collection Book from 2015 you may notice this train set cataloged as DB, it is actually an Era II DRG train set. I have poured over this book which is a useful aid in researching Marklin Z and this is the first typo I have noticed.

Produced in 2011 – 2013 this train set included two pairs of GII “Leig-Einhart” Dresden box cars permanently coupled together. Coupled to a class 86 tank locomotive this lightweight train as it is referred formed a goods train in Era II, its development followed the need to procure lightweight trains for fast freight service with speed approved to 100 km/hour. This trainset would last until 1978.

The locomotive at the head of this train is the BR 86 tank locomotive as can be seen in the photos the tanks run either side of the boiler, this design cleverly allowed for some preheating of the water tank at the same time adding stability to the locomotive operation, its limitation was only the amount of coal it could carry.

Fifteen years of production starting in 1928 yielded 775 total units for regional and branch line service. One of Germany’s longest serving steam locos the class 86 served variously throughout Germany for 60 years.

Marklin’s 81001 BR 86 locomotive is painted and lettered for Deutsche Reichsbahn-Gesellschaft (DRG), it features a 5 pole motor with 4 pairs of driving wheels and cast metal body with many detail features.

The 81001 train set is sold out at the factory but a recent search shows these to be available through various dealers.

Good luck and have fun!

Siding: an excellent resource for regular production Marklin Z is the 800 page catalog Collection Marklin Z, published by modellplan GbR, 2015. Its author Thomas Zeeb has provided the “go to guide” for collectors of Marklin Z. This number one source was included with the release of the 2015 Toy Fair loco: BR 111 with experimental paint scheme. The book and the loco were delivered in an attractive black box illustrated with its contents. Marklin item number for the set is 88422.

New Release: Marklin 89759 Steel Girder Bridge

With the new release of a steel girder bridge Marklin has further committed to finely detailed and textured laser cut kits in Z. For those who have been fortunate to discover Archistories kits this one is similarly packaged, but it is not an Archistories kit, the manufacturer of this kit is Modellbau Laffont who have produced other kits recently in the Marklin Z line-up.

For an easy introductory laser cut kit this is a good place to start, it will take about 1 – 2 hours to complete for those with a little experience perhaps longer if this is the first time completing such a kit. A fine OLFA razor knife is perfect, a pair of fine tweezers and common white glue although I prefer NOCH 61104 glue designed for this purpose.

The steel girder railroad bridge is common to all parts of the globe in one form or another because of its high strength and low cost. Usually older bridges are spotted with rust and the general rule is follow a maintenance schedule including repainting this type of bridge periodically to extend the life many years in the future. For a railroad layout a choice can be made to add weathering such as dirt, grime and rust which I will be following up with in a future post.

The bridge kit is loaded with detail including the heavy riveted plates joining angled beams, it also features a wood plank walkway with attached railing. The completed project is a well thought out heavy duty steel bridge that is rigid as a model too.

The cost of the bridge is reasonable, I bought mine for $16.00. Overall length is 4 1/4 inches and multiple bridges will be an eye catcher on a layout. Bridge supports will need to be fashioned with some type of masonry either brick or stone, these veneers are easily available, they are glued over cardboard or styrofoam. With its filigree base the light from your locos or coaches will reflect in the river below to spectacular effect.

Good luck and have fun!

Pilot Wheels: Legacy in Marklin Z

Marklin 88092 with two wheel leading truck.

With the invention of the steam locomotive in the 19th century came un-powered pilot wheels as part of its invention, they were meant to support the front end of the boiler and assist the locomotive negotiating curves. John Jervis is credited with the first locomotive design incorporating leading wheels or pilot wheels for his 1832 4-2-0 locomotive. It would be another 33 years until the design of leading wheels would be improved by William Adams, his 1865 design allowed the front bogie to slide slightly to negotiate curves and a spring mechanism to thus allow the bogie to reorient to center. A two wheel leading truck is referred to as a ‘pony’ truck, four and six wheel leading trucks are considered more stable than pony trucks for high speed service. As a point of clarification the pilot of a locomotive is located on the front of a locomotive to deflect any type obstruction which would otherwise derail the train, various designs were built into 19th and 20th century steam locomotives of a mostly filigree framework, later solid sheathing was incorporated in the streamlining of many diesel designs in the United States.

Marklin Z steam locomotives incorporate sliding lead wheel sets with a spring mechanism made of tension brass. Even in Z the leading wheels are important to running long steam locomotives successfully. It is another example of Marklin being true to the prototype even in the smallest scale.

I recently bought 88272 as ‘new dealer old stock’, it was released in the mid 2000’s as a One Time Series, it sat on a shelf for over 10 years with plenty of time for the oil to harden. I tested it at low voltage and it worked flawlessly without any hesitancy so I tried it on a large oval, the pilot wheels derailed on the first curve: hardened oil syndrome on the pilot truck pivot point as well as the trailing truck’s pivot point with no sign of hardened oil in the gearing of the driving wheels. Cleaning the loco of all the old oil and re-oiling solved the problem! Advantages with Marklin Z are the easy to diagnose and repair problems: always look for the easy answers.

After making the repair I compared the 88272 BR 42 with the 88273 BR 41 both are closely related with the same chassis and shell , leading wheels and trailing wheels on the 88273 do not include the tension brass mechanism supporting the axle on both trucks. If the slight tension created by the brass spring is too much the wheel set will deform below the surface of the driving wheels. Removing the brass tension mechanism if it is deformed or damaged is recommended, if it is left in this case derailments will ensue.

Since entering the community of Z I have been told by many that the two wheel leading truck on some Marklin Z steam locos cause derailments due to not enough weight on the front end of the locomotive, it has been advised that placing lead weights to the front end by soldering bb’s is the answer to fixing the apparent Marklin design flaw. We might all like to tinker, but as a long time collector of Marklin z gauge I found no evidence of design flaws in z by Marklin quite the opposite, I continue to marvel at locomotives and rolling stock designed for long term running characteristics which are easy to maintain and repair.

I collect Marklin mini-club as my primary railroading enterprise, but I also collect prewar Marklin 1 gauge and prewar Lionel Standard gauge. As a point of comparison I pulled out the motor and pilot wheels of my Lionel 384 from 1930. In the photos the itty bitty Marklin Z 88273 incorporates leading wheels that slide on their axle whereas the big Lionel loco restricts the leading wheels to pivot only on a vertical axis.

Photo: Lionel 384 pilot wheel and Marklin 88273: behemoth and the “Little Giant!”

Photo: Lionel 384 2-4-0 locomotive motor with driving wheels and leading wheels juxtaposed next to Marklin 88273 which incorporates a sliding axle not present in the 1930 Lionel.

I would say in closing that Marklin has already considered the leading trucks as important elements and not decoration in their design which accounts for historical accuracy and perfect operating characteristics, modification to the leading truck maybe overlooking the real problems which could be dirt or hardened oil around the pivot point or too much downward pressure from the brass tension spring. The same applies to the trailing truck. Always look for the easy answers instead of reinventing the wheel.

Good luck and have fun!

Siding: Gearing on Marklin Z gauge steam locomotives usually comprise driving wheels with connecting gears. Connecting gears are installed first followed by the driving wheels and side rods. It is a little tricky working with small parts, but the objective is to line up all of the wheel weights in correct orientation otherwise the loco will not run smoothly instead the gears will bind up. Tell those around you that you may need a 1/2 hour on your hobby or 6 hours when you make your first steam locomotive repair.

Siding: if that set of pilot wheels keeps derailing it will more than likely be dirt or hardened oil around the pivot point, pilot wheels should move freely around pivot point.

New Releases: Archistories “Signal Towers” + Marklin tank loco 88957

The perfect companion for Archistories buildings along the rails is Marklin and vice versa. Three new releases by these two companies plus one more Archistories will be the gist of this post.

Both companies of German origin go hand in hand, Archistories reaching back in time with their early Prussian design brick industrial buildings which service the railway and Marklin’s wide range of Era 2-6 locos and rolling stock. A new release by one of these companies builds on the tradition of what has been released thus far.

For Archistories two new signal towers one of brick and the other framework construction complement another interlocking tower with exposed timber released a few years back.

Variations in their kits include thus far have included framework versus brick as was the case with the mill building which can be seen here along side the new release signal tower of exposed timber/framework construction. Framework construction can be seen in Germany in a variety of uses including residential. Adding several different building types in exposed timber versus brick makes for a very interesting landscape.

Notice the mill propped by tweezers to level it out for the photo, the wheel extends below grade and it is serviced by a small motor provided in the kit. Simply soldering is required to attach two diodes in-line to the positive pole, wires thus descend below the structure and will thus be hidden from view after the building is planted in your layout’s landscape. The first step to making the mill is the wheel which is the more involved than the rest of the kit, but it is fun to start here knowing that by the end of the day that wheel will be turning wheat berry into flour for your town’s sustenance. The motor provided in the kit is shaped to perfectly conform to the buildings framework, but before proceeding you will want to confirm the motor is functioning properly just to be sure, it is highly unlikely to have a motor defect in an Archistories kit. The manufacturer suggested to me that a couple of more diodes can be installed to reduce the sound of the motor, I am a okay with the movement and sound, I don’t feel additional modification is warranted. Special Note: diodes should never be covered by electrical tape due to the potential of overheating, leave them naked so to speak!

Finding a home on the layout will require a mill race with partially dammed water to create pressure, one door is provided to the bridge that could provide access to a parking area for a truck or wagon. A Preiser figure or two will sure add scale and built into each Archistories kit are partition walls to carefully control light flow inside the mill.

If you have ever wondered what a signal tower looked like way back in the day Archistories has provided us with three examples including the two mentioned in this post. When signal towers had a purpose they housed throw levers made of brass that skilled operators would throw and pull to control semaphores and track switches. In the United States switch towers can be seen variously within large switch yards but the throw switches have been replaced with electronic push buttons. And for that matter modern control can be carried out miles away. Signal towers in the United States were so well built as was other rail infrastructure that many abandoned years ago still stand today.

Archistories has modeled their signal towers/interlocking towers with many throw levers, and they have provided large windows for good visibility, the name of the game is coordination and visibility, railways could not sustain frequent accidents or misaligned trains thus the operator of signals and switches provided a very important contribution to safe and efficient rail service.

Marklin’s new tank loco is a member of the elite new and improved steam loco design for Mini-club that includes partially new tooling including the active side rods whose movement is a lively and graceful dance, new tooling includes detailed running gear and brakes. To not mention the extensive and crisp painting and printing would be an oversight since the level of detail probably extends further than we can see, but it is reassuring that Marklin still goes further than we might require to bring the model closer to the prototype. This one being the KPEV class T12 tank locomotive with “Berlin” destination board and used in suburban traffic. Marklin 88957 is an MHI Exclusive, collectors will need to contact an MHI dealer to order this one. The Marklin Handlers Initiative constitutes those dealers who order everything Marklin produces thus guaranteeing availability of certain releases other dealers may not have access to. Having a relationship with an MHI dealer who also handles your Insider subscription will guarantee your collection grows with some of the rarer releases.

Recommended: Noch 61104 laser-cut adhesive features pin point accuracy when applying glue in small drops for laser-cut cardstock building construction: faster than applying glue with a pin or toothpick!

Good luck and happy railroading!

Your wish has been granted: 2 new releases from Archistories!!!!

It has been too long since I have put together an Archistories building kit, and just the other day I was hoping for a new release; my wish was granted two-fold with the release of a signal tower in two versions: 1. 101161- Dorpeder/Moosbach brick construction variant one and 2. 102161- Kallental/Biberbach open timber variant two.

Archistories 101161

Archistories 102161

*Photos courtesy of Archistories.

If you have not assembled an Archistories kit let me tell you to get on board and put one of these kits together. Realism with fine detailing and historical accuracy are built into each kit. Plus the best build instructions of any building kit out there for ‘Z’. The novice who takes their time and enjoys the journey will produce a building so fine family and friends will take note that this hobby of your’s is serious business.

Archistories granted permission to use two of their company photographs in this post. The photographs illustrate how nicely these buildings can look in a railroad diorama whose design and construction is equivalent fun to running trains. And very satisfactory investment of time!

Laser cut fiber buildings are the next generation, this and other developments in ‘Z’ are getting scale model railroading closer and closer to the prototype.

I ordered both kits the other day from Z Scale Hobo, they should arrive any minute although my postman is on holiday so hopefully these minutes will not pass into hours. Can you tell I am anxious to start building these signal towers????

In the meantime as I continue to wait let me mention a few words about ZScaleHobo.com. Simply posting a link to this store would not be enough, in this day and age there are internet stores popping up all the time, but ZScaleHobo.com is not your typical online retailer of trains.

Here are some of the unique (not overstated) reasons to shop here: 1. enthusiastic specialist dealer/owner Frank      2. accurate inventory posted on the website      3. prompt shipping      4. variety of hard to find parts in stock     5. well rounded products by respected manufacturers including this one     6. best prices

You won’t find a better dealer of Z scale!

Here is a link to peruse the Archistories offerings at ZScaleHobo.com:

http://zscalehobo.com/archistories/archistories.html#Z-Scale

Time to go, I hear the postman. Question: which building should I start with?

Good luck and have fun!